Here is a full list of advanced settings (parameters) for ZEN30 Double Switch VER 4.10 and VER 3.20 firmware for Hardware Versions 3 & 4. Some parameters were added in later firmware updates so please make sure you're on the latest firmware to have all of the settings below available (not all are available on 500 series Hardware Versions 1 & 2. You can view the change log for the ZEN30 here.
LED Indicator Control
Parameter 1: Choose if you want the LED indicator to turn on when the dimmer (light) is on or off, or if you want it to remain on or off at all times. This setting is for the top status indicator only.
Values: 0 – LED indicator is on when switch is off, LED indicator is off when switch is on (default); 1 – ED indicator is on when switch is on, LED indicator is off when switch is off; 2 – LED indicator is always off and LED’s don’t indicate brightness level during dimming; 3 – LED indicator is always on. NOTE: tap the upper paddle 6 times quickly to change this mode.
Size: 1 byte dec
Parameter 2: Choose if you want the LED indicator to turn on when the relay is on or off, or if you want it to remain on or off at all times
Values: 0 – LED indicator is on when relay is off, LED indicator is off when relay is on (default); 1 – LED indicator is on when relay is on, LED indicator is off when relay is off; 2 – LED indicator is always off; 3 – LED indicator is always on. NOTE: tap the relay button 6 times quickly to change this mode.
Size: 1 byte dec
Parameter 3: Choose the color of the LED indicators for the dimmer.
Values: 0 – white (default); 1 – blue; 2 – green; 3 – red.
Size: 1 byte dec
Parameter 4: Choose the color of the LED indicator for the relay.
Values: 0 – white (default); 1 – blue; 2 – green; 3 – red.
Size: 1 byte dec
Parameter 5: Choose the LED indicators’ brightness level for the dimmer.
Values: 0 – bright (100%); 1 – medium (60%); 2 – low (30%). Default: 1.
Size: 1 byte dec
Parameter 6: Choose the LED indicators’ brightness level for the relay.
Values: 0 – bright (100%); 1 – medium (60%); 2 – low (30%). Default: 1.
Size: 1 byte dec
Parameter 7: Choose if you want the LED indicators next to the dimmer to light up when a scene is selected. You’ll see 1 to 5 LEDs light up for 1 – 5 tap triggers and 6 LEDs light up for the press-and-hold trigger of any paddle / button used.
Values: 0 – LEDs enabled to indicate scene triggers; 1 – LEDs disabled to indicate scene triggers (default).
Size: 1 byte dec
On/Off Paddle Orientation for the Dimmer
Parameter 27: Choose if you want the upper paddle to turn the light on or turn the light off when tapped.
Values: 0 – Upper paddle turns the light on, lower paddle turns it off (default); 1 – Upper paddle turns the light off, lower paddle turns it on; 2 – Any paddle turns light on/off.
Size: 1 byte dec
Auto Turn-Off Timer
Parameter 8: Use this parameter to set the time after which you want the dimmer to automatically turn off once it has been turned on. The number entered as value corresponds to the number of minutes.
Values: 0 – timer disabled (default); 1 – 65535 (minutes).
Size: 4 byte dec
Parameter 10: Use this parameter to set the time after which you want the relay to automatically turn off once it has been turned on. The number entered as value corresponds to the number of minutes.
Values: 0 – timer disabled (default); 1 – 65535 (minutes).
Size: 4 byte dec
Auto Turn-On Timer
Parameter 9: Use this parameter to set the time after which you want the dimmer to automatically turn on once it has been turned off. The number entered as value corresponds to the number of minutes.
Values: 0 – timer disabled (default); 1 – 65535 (minutes).
Size: 4 byte dec
Parameter 11: Use this parameter to set the time after which you want the relay to automatically turn on once it has been turned off. The number entered as value corresponds to the number of minutes.
Values: 0 – timer disabled (default); 1 – 65535 (minutes).
Size: 4 byte dec
On Off Status After Power Failure
Parameter 12: Set the on/off status of the device after power failure.
Values: 0 – dimmer and relay forced to off (regardless of state prior to power outage);
1 – dimmer forced to off, relay forced to on;
2 – dimmer forced to on, relay forced to off;
3 – remembers and restores on/off status for dimmer and relay after power failure (default);
4 – remembers and restores on/off status for dimmer, relay forced to on;
5 – remembers and restores on/off status for dimmer, relay forced to off;
6 – dimmer forced to on, remembers and restores on/off status for relay;
7 – dimmer forced to off, remembers and restores on/off status for relay;
8 – dimmer and relay forced to on.
Size: 1 byte dec
Ramp Rate Control for the Dimmer
Parameter 13: Adjust the ramp rate ON for your dimmer when the top paddle is pressed (physical ramp rate on). Values correspond to the number of seconds it take for the dimmer to reach full brightness when operated manually.
Values: 1 – 99 (seconds). 0 – instant on. Default: 0.
Size: 1 byte dec
NOTE: On all other previous firmware versions, this setting was used for all ramp rate control (to adjust behavior for on/off physical and Z-Wave ramp rate). The default value for this parameter used to be 1.
Parameter 31: Adjust the ramp rate OFF for your dimmer when the bottom paddle is pressed (physical ramp rate off). Values correspond to the number of seconds it take for the dimmer to turn off when operated manually.
Values: 1 – 99 (seconds). 0 – instant off. Default: 2.
Size: 1 byte dec
Parameter 32: Adjust the ramp rate ON for your dimmer when a Z-Wave command is sent to turn the dimmer on (Z-Wave ramp rate on). Values correspond to the number of seconds it take for the dimmer to reach full brightness when operated via Z-Wave.
Values: 1 – 99 (seconds). 0 – instant on. 255 – match physical. Default: 255.
Size: 1 byte dec
Parameter 33: Adjust the ramp rate OFF for your dimmer when a Z-Wave command is sent to turn the dimmer off (Z-Wave ramp rate off). Values correspond to the number of seconds it take for the dimmer to turn off when operated via Z-Wave.
Values: 1 – 99 (seconds). 0 – instant off. 255 – match physical. Default: 255.
Size: 1 byte dec
Parameter 22: Choose if you would like to match the Z-Wave on/off ramp rate with the manual ramp rate or set it separately in your hub.
Values: 0 – Z-Wave on/off ramp rate matches the manual ramp rate set in Parameter 13 (default). 1 – Z-Wave on/off ramp rate is set separately through its command class in the hub.
Size: 1 byte dec
(parameter removed in firmware 1.05)
Minimum and Maximum Brightness for the Dimmer
Parameter 14: Set the minimum brightness level (in %) for the dimmer. You won’t be able to dim the light below the set value.
Values: 1 – 99 (%). Default: 1.
Size: 1 byte dec
Parameter 15: Set the maximum brightness level (in %) for the dimmer. You won’t be able to add brightness to the light beyond the set value.
Values: 1 – 99 (%). Default: 99.
Size: 1 byte dec
Single and Double Tap Function for the Dimmer
Parameter 17: Choose if you want the dimmer to turn on to full brightness or custom brightness level after you double-tap the upper paddle.
Values: 0 - enable double tap to full brightness (99); 1 - custom value set in Parameter 23; 2 - enable double tap to maximum brightness (turn on to the value set in Parameter 15); 3 - disable double tap to full brightness.
Default: 0.
Size: 1 byte dec
Parameter 18: Choose what you'd like the dimmer to do when you tap the upper paddle once.
Values: 0 – the light will turn on to the last brightness level (default); 1 – the light will turn on to the custom brightness level set in Parameter 23; 2 – the light will turn on to the maximum brightness level set in Parameter 15; 3 – the light will turn on to full brightness.
Size: 1 byte dec
Smart Bulb Mode: Enable/Disable Paddle / Z-Wave Control
Parameter 19: Enable or disable direct manual and Z-Wave control of the light connected to the dimmer. Works great for smart bulb control. If disabled, the dimmer will no longer control the connected bulb directly but will still send on/off and brightness reports to the hub so you can use them to create automations for your smart bulbs or other switches. Scenes and other functionality will still be available through paddles.
Values: 0 – manual control disabled. 1 – manual control enabled (default). 2 – manual and Z-Wave control disabled.
Size: 1 byte dec
Parameter 20: Enable or disable direct manual and Z-Wave control of the load connected to the relay button. Works great for smart bulb or any type of remote / scene control. If disabled, the relay button will no longer control the connected load directly but will still send on/off reports to the hub so you can use them to create automations for your smart bulbs or other devices. Scenes and other functionality will still be available through the button.
Values: 0 – manual control disabled. 1 – manual control enabled (default). 2 – manual and Z-Wave control disabled.
Size: 1 byte dec
Parameter 24: Set reporting behavior for the dimmer when physical control is disabled.
Values: 0 – dimmer reports on/off status and brightness level and changes LED indicator state even if physical and Z-Wave control is disabled (default). 1 – dimmer doesn't report on/off/brightness status changes and it doesn't change the LED indicator state when physical (and Z-Wave) control is disabled and paddles are pressed or the dimmer receives on/off commands from the hub.
Parameter 25: Set reporting behavior for the relay when physical control is disabled.
Values: 0 – relay reports on/off status and changes LED indicator state even if physical and Z-Wave control is disabled (default). 1 – relay doesn't report on/off status changes and it doesn't change the LED indicator state when physical (and Z-Wave) control is disabled and the button is pressed or the relay receives on/off commands from the hub.
Physical Dimming Speed for the Dimmer
Parameter 21: Choose how many seconds it takes for the dimmer to go from 0% to 100% brightness when pressing and holding the paddle. Increase the value to decrease the dimming speed.
Values: 1 – 99 (seconds). Default: 4.
Size: 1 byte dec
Custom Brightness Level On
Parameter 23: Set custom brightness level (in %) for the dimmer to come on to at single tap.
Values: 0 – last brightness level (default); 1 – 99 (%) for custom brightness level.
Size: 1 byte dec
Night Light Mode
Parameter 26: Set the brightness level the dimmer will turn on to when off and when the lower paddle is held DOWN for 2.5-3 seconds.
Values: 0 – feature disabled; 1 – 99 (%). Default: 20.
Size: 1 byte dec
Enable/Disable Scene Control
Parameter 28: Enable or disable scene control functionality for quick double tap triggers on the dimmer paddles.
Values: 0 – scene control disabled. 1 – scene control enabled (default).
Size: 1 byte dec
Parameter 29: Enable or disable scene control functionality for quick double tap triggers on the relay button.
Values: 0 – scene control disabled. 1 – scene control enabled (default).
Size: 1 byte dec
Enable/Disable Programming on the Dimmer Paddles
Parameter 30: Enable or disable programming functionality on the dimmer paddles. If this setting is disabled, then inclusion, exclusion, smart bulb mode no longer work when dimmer paddles are activated (factory reset and scene control will still work) - that means you can now use triple-tap triggers on the dimmer for scenes and remote control of other devices.
Values: 0 – programming enabled (default). 1 – programming disabled.
Size: 1 byte dec
MANUAL CONTROL
Dimmer Upper Paddle:
1 x tap: load on to last / custom brightness; Scene 1, attribute 00
2 x tap: on to full / max brightness; Scene 1, attribute 03
3 x tap: enter inclusion (pairing) mode; Scene 1, attribute 04
4 x tap: Scene 1, attribute 05
5 x tap: Scene 1, attribute 06
6 x tap: change LED indicator mode (see parameter 1)
press and hold: increase brightness level; Scene 1, attribute 02
release: Scene 1, attribute 01
Lower Paddle:
1 x tap: load off; Scene 2, attribute 00
2 x tap: Scene 2, attribute 03
3 x tap: enter exclusion (unpairing) mode; Scene 2, attribute 04
4 x tap: Scene 2, attribute 05
5 x tap: Scene 2, attribute 06
press and hold: decrease brightness level; Scene 2, attribute 02
release: Scene 2, attribute 01
tap-tap-tap-tap-and-hold: change physical / Z-Wave control mode (see parameter 19)
hold for 15 seconds: initiate factory reset (then release and hold the upper paddle to complete the reset)
Relay Button:
1 x tap: load on / off; Scene 3, attribute 00
2 x tap: Scene 3, attribute 03
3 x tap: enter inclusion (pairing) mode; Scene 3, attribute 04
4 x tap: Scene 3, attribute 05
5 x tap: Scene 3, attribute 06
6 x tap: change LED indicator mode (see parameter 2)
press and hold: increase brightness level; Scene 3, attribute 02
release: Scene 3, attribute 01
How to Access the Advanced Settings:
All ZEN30 switches can be updated via OTA firmware updates, here is how to do that. You can access all firmware files here after you register your product and create an account here. There are currently 3 different hardware versions (1.0, 2.0, and 3.0) of the product so you need to make sure to apply the correct firmware for your version. Questions? Just reach out to our tech support team.
