Here is a full list of advanced settings (parameters) for the ZEN74 Toggle Dimmer 800LR :
Toggle Orientation
Parameter 1: Choose if you want to turn the light on or turn the light off when you toggle the switch up.
Values: 0 – Toggle up turns the light on, toggle down turns it off; 1 – Toggle up turns the light off, toggle down turns it on; 2 – Toggle any direction to turn the light on/off (change state). Default: 0.
Size: 1 byte dec
LED Indicator
Parameter 2: Choose if you want the LED indicator to turn on when the dimmer (light) is on or off, or if you want it to remain on or off at all times.
Values: 0 – LED on when switch off; 1 - LED on when switch on; 2 - LED always off; 3 - LED always on. Default: 0.
Size: 1 byte dec
Auto Turn-Off Timer
Parameter 3: Use this parameter to enable or disable the auto turn-off timer function (the time after which you want the switch to automatically turn off once it has been turned on).
Values: 0 – timer disabled; 1 – 65535 (minutes). Default: 0
Size: 4 byte dec
Auto Turn-On Timer
Parameter 5: Use this parameter to enable or disable the auto turn-on timer function (the time after which you want the dimmer to automatically turn on once it has been turned off).
Values: 0 – timer disabled; 1 – 65535 (minutes). Default: 0
Size: 4 byte dec
Association Reports
Parameter 7: Choose which physical and Z-Wave triggers should prompt the dimmer to send a status change report to the associated devices. See values for details.
Values: 0 – none; 1 – physical tap on ZEN74 only; 2 - physical tap on connected 3-way switch only; 3 - physical tap on ZEN74 or connected 3-way switch; 4 - Z-Wave command from hub; 5 - physical tap on ZEN74 or Z-Wave command from hub; 6 - physical tap on connected 3-way switch or Z-Wave command from hub; 7 - physical tap on ZEN74 / connected 3-way switch or Z-Wave command from hub; 8 - timer only; 9 - physical tap on ZEN74 or timer; 10 - physical tap on connected 3-way switch or timer; 11 - physical tap on ZEN74 / connected 3-way switch or timer; 12 - Z-Wave command from hub or timer; 13 - physical tap on ZEN74, Z-Wave command from hub, or timer; 14 - physical tap on ZEN74 / connected 3-way switch, Z-Wave command from hub, or timer; 15 - all of the above. Default: 15
Size: 1 byte dec
On Off Status After Power Failure
Parameter 8: Set the on off status for the switch after power failure.
Values: 0 – forced to OFF (regardless of state prior to power outage); 1 – forced to ON (regardless of state prior to power outage); 2 – remembers and restores on/off status after power failure. Default: 2
Size: 1 byte dec
Physical Ramp Rate ON
Parameter 9: Adjust the ramp rate ON for your dimmer when it's toggled up (physical ramp rate on). Values correspond to the number of seconds it takes for the dimmer to reach full brightness when operated manually.
Values: 0 – instant on; 1 – 99 (seconds). Default: 0.
Size: 1 byte dec
Minimum Brightness
Parameter 10: Set the minimum brightness level (in %) for your dimmer. You won’t be able to dim the light below the set value.
Values: 1 – 99 (%). Default: 1.
Size: 1 byte dec
Maximum Brightness
Parameter 11: Set the maximum brightness level (in %) for your dimmer. You won’t be able to add brightness to the light beyond the set value. Note: if Parameter 12 is set to value 0, Parameter 11 is automatically disabled.
Values: 1 – 99 (%). Default: 99.
Size: 1 byte dec
Double Tap Up
Parameter 12: Choose what you'd like the dimmer to do when you toggle it up twice quickly. This is a different setting than scene control so remember to program only one of the settings to avoid logical conflict.
Values: 0 – the light will turn on to full brightness; 1 – the light will turn on to the custom brightness level set in parameter 18; 2 – the light will turn on to the maximum brightness level set in Parameter 11; 3 – double tap disabled. Default: 0
Size: 1 byte dec
Enable/Disable Scene Control
Parameter 13: Enable or disable scene control functionality for quick multi tap triggers.
Values: 0 – scene control disabled. 1 – scene control enabled. Default: 0.
Size: 1 byte dec
Load Control (Smart Bulb Mode)
Parameter 15: Enable or disable physical and Z-Wave on/off and dimming control. Disable both physical toggle and Z-Wave control for smart bulbs (use central scene triggers). Scene control and other functionality will still be available from physical toggle.
Values: 0 – physical toggle control disabled; 1 – physical toggle control enabled; 2 – physical toggle and Z-Wave control disabled. Default: 1
NOTE: hold the toggle up for 10 seconds until the LED indicator starts blinking, then within 2 seconds, toggle the switch up 5 times quickly to change this mode. The LED indicator will stay solid green for 3 seconds to confirm the change.
Size: 1 byte dec
Dimming Speed
Parameter 16: Set the time it takes to get from 0% to 100% brightness when holding the toggle up (physical dimming). The number entered as value corresponds to the number of seconds.
Values: 1 – 99 (seconds). Default: 5.
Size: 1 byte dec
Physical Custom Brightness Level On
Parameter 18: Set the custom brightness level (instead of the last set brightness level) you want the dimmer to come on to when you single tap or double tap the toggle up (see parameters 12 and 25).
Values: 0 – last brightness level; 1 – 99 (%) for custom brightness level. Default: 0
Size: 1 byte dec
Multilevel Dimming Reports
Parameter 20: Choose how you'd like the dimmer to report when the toggle is tapped and held and physical / Z-Wave control is enabled or disabled. See parameter 15 (smart bulb mode) for details.
Values: 0 – send basic set report for each brightness level to hub when physical / Z-Wave control is disabled for physical dimming when the toggle is manually tapped/ held; report final brightness level only (basic set report) for physical dimming when the toggle is manually tapped/ held and physical / Z-Wave control is enabled; always report final brightness level only (via multilevel reports) for Z-Wave control regardless of the physical / Z-Wave control mode. 1 – report final brightness level only for physical dimming, regardless of the physical / Z-Wave control mode. 2 – send multilevel report for each brightness level to hub when physical / Z-Wave control is disabled for physical dimming when the toggle is manually tapped/ held; report final brightness level only (multilevel report) for physical dimming when the toggle is manually tapped/ held and physical / Z-Wave control is enabled; always report final brightness level only (via multilevel reports) for Z-Wave control regardless of the physical / Z-Wave control mode. Default: 2.
Size: 1 byte dec
Disabled Load Behavior
Parameter 21: Set reporting behavior for disabled physical control of the load connected to the dimmer (smart bulb mode).
Values: 0 – switch reports on/off status and changes LED indicator state; 1 – switch doesn't report on/off status or change LED indicator status. Default: 0.
Size: 1 byte dec
Night Light
Parameter 22: Set the brightness level the dimmer will turn on to when off and when the toggle is held DOWN for 2.5-3 seconds.
Values: 0 – feature disabled; 1 – 99 (%). Default: 20.
Size: 1 byte dec
LED Indicator Color
Parameter 23: Choose the color of the LED indicator.
Values: 0 – white; 1 – blue; 2 – green; 3 – red. Default: 1.
Size: 1 byte dec
LED Indicator Brightness
Parameter 24: Choose the LED indicator's brightness level
Values: 0 – bright (100%); 1 – medium (60%); 2 – low (30%). Default: 1.
Size: 1 byte dec
Single Tap Up
Parameter 25: Choose what you'd like the dimmer to do when you toggle it up once. This is a different setting than scene control so remember to program only one of the settings to avoid logical conflict.
Values: 0 – on to the last brightness level; 1 – on to the custom brightness (from param 18); 2 – on to max brightness (from param 11); 3 – on to full brightness. Default: 0.
Size: 1 byte dec
Disable Toggle Programming
Parameter 26: Enable or disable programming functionality on the dimmer toggle. If this setting is disabled, then inclusion, exclusion, smart bulb mode no longer work when a dimmer toggle sequence is activated (factory reset and scene control will still work) - that means you can now use triple-tap triggers on the switch for scenes and remote control of other devices.
Values: 0 – programming enabled; 1 – programming disabled. Default: 0.
Size: 1 byte dec
Physical Ramp Rate Off
Parameter 27: Adjust the ramp rate OFF for your dimmer when the dimmer is toggled down (physical ramp rate off). Values correspond to the number of seconds it takes for the dimmer to completely turn off when operated manually.
Values: 0 – instant off; 1 – 99 (seconds). Default: 2.
Size: 1 byte dec
Z-Wave Ramp Rate ON
Parameter 28: Adjust the ramp rate ON for your dimmer when controlled with Z-Wave for a smooth fade-in effect (in seconds). Values correspond to the number of seconds it takes for the dimmer to reach full brightness when controlled with Z-Wave commands. Use value 255 to match the physical settings in parameter 9.
Values: 0 – instant on; 1 – 99 (seconds); 255 – match physical ramp rate. Default: 255.
Size: 1 byte dec
Z-Wave Ramp Rate OFF
Parameter 29: Adjust the ramp rate OFF for your dimmer when controlled with Z-Wave for a smooth fade-out effect (in seconds). Values correspond to the number of seconds it takes for the dimmer to completely turn off when controlled with Z-Wave commands. Use value 255 to match the physical settings in parameter 27.
Values: 0 – instant off; 1 – 99 (seconds); 255 – match physical ramp rate. Default: 255.
Size: 1 byte dec
Remote Dimming Speed
Parameter 30: Set the time it takes to get from 0% to 100% brightness on dimmers and smart bulbs directly associated with your dimmer in Groups 3 and 4 when pressing and holding the toggle (physical dimming) on your dimmer. The number entered as value corresponds to the number of seconds.
Values: 1 – 99 (seconds). Default: 5.
Size: 1 byte dec
Disable LED Indicator Flash On Setting Changes
Parameter 32: Enable / disable LED indicator for setting changes. Choose if you want the LED indicators to flash whenever a parameter (settings) is adjusted on the device to confirm the change. Disable this feature if you're using the LED indicators in automations.
Values:
0 – LED indicators flash to confirm a setting change; 1 - LED indicators don't flash if a setting is changed. Default: 0
Size: 1 byte dec
On Off Switch Mode
Parameter 33: Convert the dimmer to an on off switch. When enabled, the dimmer will behave as a switch without the ability to dim. All ramp rates will be set to instant ON/OFF and the brightness level will locked at 99%.
Values: 0 – disabled; 1 – enabled. Default: 0.
Size: 1 byte dec
Z-Wave Custom Brightness On
Parameter 34: Set the custom brightness level (or leave the last brightness level) for Z-Wave ON basic set commands.
Values: 0 – last brightness level; 1-99 (%). Default: 0.
Size: 1 byte dec
MANUAL CONTROL
Toggle Up:
1 x tap: load on; Scene 1, attribute 00
2 x tap: Scene 1, attribute 03
3 x tap: enter inclusion (pairing) mode (only if the switch is not included to the hub); Scene 1, attribute 04
4 x tap: Scene 1, attribute 05
5 x tap: Scene 1, attribute 06
held: increase brightness, Scene 1, attribute 01
released: Scene 1, attribute 02
Toggle Down:
1 x tap: load off; Scene 2, attribute 00
2 x tap: Scene 2, attribute 03
3 x tap: enter exclusion (unpairing) mode; Scene 2, attribute 04
4 x tap: Scene 2, attribute 05
5 x tap: Scene 2, attribute 06
held: decrease brightness, Scene 2, attribute 01
released: Scene 2, attribute 02
held for 10 seconds (LED indicator starts blinking): enter the setting menu >> 5 x tap down for factory reset; 5 x tap up to change LED bulb mode (see parameter 11); 2 x tap down to enable the range test tool.
How to access advanced settings for the ZEN74 Toggle Dimmer on your hub:
The ZEN74 800LR Toggle Switch supports the following command classes:
- Z-Wave Plus Info V2
- Security 2 V1
- Supervision V1
- Transport Service V2
- Basic V2
- Association V3
- Association Group Information V3
- Multi Channel Association V3
- Version V3
- Manufacturer Specific V2
- Device Reset Locally V1
- Power Level V1
- Indicator V3
- Firmware Update Meta Data V5
- Configuration V4
- Central Scene V3
- Switch Multilevel V4
All ZEN74 dimmers can be updated via OTA firmware updates, here is how to do that. You can access all firmware files here after you register your product and create an account here. Questions? Just reach out to our tech support team.
