ZEN05 Outdoor Smart Plug FAQs

Frequently Asked Questions About the ZEN05 Outdoor Smart Plug

Find the answers to your questions quickly by searching key words!

Press the CTRL and F keys at the same time on your keyboard. A little box should pop up in your browser window.
Type in a key word in your question like "hub" or "compatible". You should see your key word highlighted every time it is mentioned on the page.
Use the arrow keys in the search box to jump to each instance that your key word is mentioned.

Angled Plug ZEN05 ZEn05 Outdoor Smart Plug S2 Security ZEN05

INSTALLATION QUESTIONS

Can the ZEN05 be installed outdoors?

Yes. The ZEN05 is rated IP65 for outdoor use.
This product should be installed indoors upon completion of any building renovations.
Do not install the device in a place with direct sun exposure, high temperature, or humidity.
Keep it away from chemicals, water, and dust.

What is the operating temperature of the ZEN05?

32° – 104° F (0-40° C)

Will the ZEN05 work in temperatures outside of the listed operating temperatures?

The specification of the Z-Wave chip requires environments of no less than 32 F and no more than 104 F. This is why we list the operating temperature at 32-104 F; the same applies for all Z-Wave devices we know of since they shouldn't be installed in environments that often drop below 32F or exceed 104 F.
It's likely that you may lose Z-Wave control during super cold periods.

Is the ZEN05 available in other colors?

No. The ZEN05 is available in black only.

What are the dimensions of the ZEN05? How big is the device?

3.25" tall, 2.25" wide, 1.5" deep
Cord Length: 6.5"

Will this cover up the other outlet or can other devices be plugged in?

The ZEN05 plug leaves enough space for the other outlet in your receptacle and will not cover it. You can even fit two smart plugs in the same receptacle!

How could I mount the ZEN05 on the wall?

The ZEN05 has a mounting hole on the top tab where the plug comes out of the device with a large round space and a narrow top.
You'll want to affix your screw in the wall, then you can simply place the ZEN05 over the screw and slide the unit down so that the screw locks in at the narrow part of the top. You will not need to disassemble the unit.

What kind of devices can or can't I connect to the ZEN05?

What Devices Can I Use with My ZEN05 Outdoor Plug?

Could I use the ZEN05 to power a low voltage lighting transformer like this one here for my landscape lighting?

NO, it is not a supported load for the ZEN05.
For an installation like this, we recommend using either the ZEN16 Multirelay or ZEN17 Universal Relay between the 12V output side of your transformer and landscaping lightning. This scenario is safe for the ZEN16 or ZEN17 since the 12V is a constant voltage from your magnetic transformer (coil transformer – not an electronic one). With the ZEN16 or ZEN17 you'll also be able to control multiple zones of landscape lightning.

Can I use the ZEN05 to power an electric heater?

NO. Even if a heating appliance is within the power range of these plugs, we wouldn't recommend automating electric heaters and similar appliances. This is a big fire and safety hazard, since not only should these devices not be left unattended when on, but there's always the risk of accidentally turning it on remotely; this is a UL safety recommendation.

What is the warranty coverage for the ZEN05 Smart Plug?

Zooz 500 series devices are covered by a 12 month warranty. Zooz 700 and 800 series devices are covered by a standard 1-year warranty and by an extended 5-year warranty if registered within 30 days of purchase. Please register your device here and review the full warranty policy here.

Where can I find the ZEN05 device manual?

Manual for the Zooz 700 Series Z-Wave Plus Outdoor Smart Plug ZEN05 (PDF)

PRODUCT FUNCTIONALITY QUESTIONS

What kind of load is the ZEN05 rated for? What is its maximum rating?

960W incandescent, 150W LED bulbs, 15A resistive, 1/3 HP fan motors

Does the ZEN05 have energy or power monitoring?

YES - for the 800 series version only. The 700 series does not have energy or power monitoring available at this time.
Once power monitoring is added, the plug will track energy use in real time which can then be processed into insightful data logs. If your Z-Wave hub gives you access to advanced settings, you can decide how often the plug reports energy information to your system.

What security level does the ZEN05 pair to my controller or hub with?

The highest level of security the ZEN05 supports is S2 Authenticated.

Will the ZEN05 act as a signal repeater for other Z-Wave devices in my network?

Yes. Your Z-Wave hub decides which devices to use to reach other Z-Wave devices. Any non-battery powered Z-Wave device will act as a signal repeater; it would be up to your hub whether or not it will be used in a communication route.

Z-WAVE QUESTIONS

Do I need a Z-Wave hub to buy this device?

No. The ZEN05 Outdoor Plug has a button so you can have manual on/off control of the outlet and can be used as such without a Z-Wave hub; however, to control the device remotely and access the advanced features, you would need a Z-Wave hub. The ZEN05 communicates via Z-Wave and would require a hub to allow you to control it remotely.
To control any of our Z-Wave devices remotely through your smart phone, you'll need a compatible Z-Wave hub. These devices require a central controller that communicates with them and sends commands. Once you have a controller, you would download that controller's dedicated app on your phone and control your connected devices through that app.

Will I still be able to control the plug manually if my Z-Wave hub is down or offline?

Yes. The ZEN05 functions like a regular plug and can control the connected load if the hub is offline.
To control the device manually, you press the Z-Wave button once for on/off control.

Is the ZEN05 plug compatible with my hub?

You can find a list of compatible hubs for a given device under the Works With section on the product's page. Here is the list of hubs compatible with the ZEN05.

Will the ZEN05 work with my alarm panel?

Alarm panels like Alarm.com will typically only support single switches, door locks, select thermostats, and any authorized items on their list. We would recommend reaching out to your alarm panel company to verify compatibility and to get the latest on any device integrations they may be working on.
The ZEN05 Outdoor Plug should pair, but you would not have access to the advanced settings. It would be up to your alarm panel to integrate the device, as it follows Z-Wave protocol and has been Z-Wave certified. There is nothing we can change on our end to have the device be recognized correctly; Alarm.com would have to support the integration. Read more about alarm panel compatibility here.

Can I connect the ZEN05 directly to my Amazon Alexa, Google Home, or other smart speaker?

No. Smart speakers like Alexa or Google are not equipped with a Z-Wave chip and are not Z-Wave gateway controllers.
Smart speakers are integrated with certain Z-Wave hubs, like SmartThings or Hubitat, which is how you can have voice control of your Z-Wave devices from your smart speakers.
Without a compatible Z-Wave hub, no Z-Wave products will function correctly with Alexa or Google alone.

Where do I find all of my plug's advanced settings?

ZEN05 Outdoor Plug Advanced Settings

How do I add the plug to my Z-Wave hub?

How can I tell what firmware my ZEN05 is running on?

The firmware that your device is shipped with should be printed on the back of the device where the model specifications are. If your hub supports and properly integrates the device, you should also see the firmware listed in your Z-Wave interface.
Firmware that is listed as 1.01 (or any other value with a 0 in the middle) in the ZEN05's change log may display as 1.1 in your hub.

How do I update the firmware of my ZEN05?

Some Z-Wave hubs have a built-in firmware updater that you can use. Otherwise, we recommend using the PC Controller tool on the Simplicity Studio Software as described here. You will need to register your device in order to have access to Zooz firmware files.

How long does the update take? How do I know when it's finished?

Firmware updates should usually take anywhere from 5 to 15 minutes depending on connection quality and how much information needs to actually be updated on a given device.
- If it is taking longer than that, please try to bring the hub / controller closer to the device that is being updated.

Where can I find the history of changes and firmware updates for the ZEN05?

ZEN05 Outdoor Smart Plug Change Log

What series Z-Wave chip does the ZEN05 use?

The ZEN05 uses a 700 series Z-Wave chip. We are in the process of updating this model to the new 800 series Z-Wave chip so it should be 800 series by the end of 2023.

Is the ZEN05 available in other Z-Wave frequencies?

The ZEN05 is currently available in 908.42 MHz (US) frequency only. We do not currently have plans to release it in EU or AU frequency.

Check out the Zooz Knowledge Base for free support articles about the ZEN05 Outdoor Plug (and all of our devices)!