Here is a full list of advanced settings (parameters) for the ZEN77 Dimmer Switch:
Some parameters were added in later firmware updates so please make sure you're on the latest firmware to have all of the settings below available. You can view the change log for the ZEN77 here.
On/Off Paddle Orientation
Parameter 1: Choose if you want the upper paddle to turn the light on or turn the light off when tapped.
Values: 0 – Upper paddle turns the light on, lower paddle turns it off (default); 1 – Upper paddle turns the light off, lower paddle turns it on; 2 – Any paddle turns light on/off.
Size: 1 byte dec
LED Indicator Control
Parameter 2: Choose if you want the LED indicator to turn on when the switch (light) is on or off, or if you want it to remain on or off at all times.
Values: 0 – LED indicator is on when switch is off, LED indicator is off when switch is on (default); 1 – LED indicator is on when switch is on, LED indicator is off when switch is off; 2 – LED indicator is always OFF; 3 – LED indicator is always ON. NOTE: tap the upper paddle 6 times quickly to change this mode.
Size: 1 byte dec
Parameter 23: Choose the color of the LED indicator.
Values: 0 – white; 1 – blue (default); 2 – green; 3 – red.
Size: 1 byte dec
Parameter 24: Choose the LED indicator's brightness level.
Values: 0 – bright (100%); 1 – medium (60%); 2 – low (30%). Default: 1.
Size: 1 byte dec
Parameter 32: Enable / disable LED indicator for setting changes. Choose if you want the LED indicators to flash whenever a parameter (settings) is adjusted on the device to confirm the change. Disable this feature if you're using the LED indicators in automations.
Values:
0 – LED indicators flash to confirm a setting change (default)
1 - LED indicators don't flash if a setting is changed
Size: 1 byte dec
Auto Turn-Off Timer
Parameter 3: Use this parameter to enable or disable the auto turn-off timer function (the time after which you want the switch to automatically turn off once it has been turned on).
Values: 0 – timer disabled (default); 1 – 65535 (minutes).
Size: 4 byte dec
Auto Turn-On Timer
Parameter 5: Use this parameter to enable or disable the auto turn-on timer function (the time after which you want the switch to automatically turn on once it has been turned off).
Values: 0 – timer disabled (default); 1 – 65535 (minutes).
Size: 4 byte dec
Association Reports
Parameter 7: Choose which physical and Z-Wave triggers should prompt the dimmer to send a status change report to associated devices.
Values: 0 – none; 1 – physical tap on ZEN77 only; 2 – physical tap on connected 3-way switch only; 3 – physical tap on ZEN77 or connected 3-way switch; 4 – Z-Wave command from hub; 5 – physical tap on ZEN77 or Z-Wave command from hub; 6 – physical tap on connected 3-way switch or Z-Wave command from hub; 7 – physical tap on ZEN77 / connected 3-way switch or Z-Wave command from hub; 8 – timer only; 9 – physical tap on ZEN77 or timer; 10 – physical tap on connected 3-way switch or timer; 11 – physical tap on ZEN77 / connected 3-way switch or timer; 12 – Z-Wave command from hub or timer; 13 – physical tap on ZEN77, Z-Wave command from hub, or timer; 14 – physical tap on ZEN77 / connected 3-way switch, Z-Wave command from hub, or timer; 15 – all of the above. Default: 15.
Size: 1 byte dec
On Off Status After Power Failure
Parameter 8: Set the on off status for the switch after power failure.
Values: 0 – forced to OFF (regardless of state prior to power outage); 1 – forced to ON (regardless of state prior to power outage); 2 – remembers and restores on/off status after power failure (default)
Size: 1 byte dec
Ramp Rate Control
Parameter 9: Adjust the ramp rate ON for your dimmer when the top paddle is pressed (physical ramp rate on). Values correspond to the number of seconds it take for the dimmer to reach full brightness when operated manually.
Values: 1 – 99 (seconds). 0 – instant on. Default: 0.
Size: 1 byte dec
NOTE: On all other previous firmware versions including 1.0, 10.0, and 10.10, this setting was used for all ramp rate control (to adjust behavior for on/off physical and Z-Wave ramp rate). The default value for this parameter used to be 1.
Parameter 27: Adjust the ramp rate OFF for your dimmer when the bottom paddle is pressed (physical ramp rate off). Values correspond to the number of seconds it take for the dimmer to turn off when operated manually.
Values: 1 – 99 (seconds). 0 – instant off. Default: 2.
Size: 1 byte dec
Parameter 28: Adjust the ramp rate ON for your dimmer when a Z-Wave command is sent to turn the dimmer on (Z-Wave ramp rate on). Values correspond to the number of seconds it take for the dimmer to reach full brightness when operated via Z-Wave.
Values: 1 – 99 (seconds). 0 – instant on. 255 – match physical. Default: 255.
Size: 1 byte dec
Parameter 29: Adjust the ramp rate OFF for your dimmer when a Z-Wave command is sent to turn the dimmer off (Z-Wave ramp rate off). Values correspond to the number of seconds it take for the dimmer to turn off when operated via Z-Wave.
Values: 1 – 99 (seconds). 0 – instant off. 255 – match physical. Default: 255.
Size: 1 byte dec
Parameter 33: Convert the dimmer to a switch. When enabled, the dimmer will act as a switch. All ramp rates will be set to instant ON/OFF and the brightness level will locked at 99%
Values: 0 - disabled. 1 - enabled. Default: 0.
Size: 1 byte dec
Minimum and Maximum Brightness
Parameter 10: Set the minimum brightness level (in %) for your dimmer. You won’t be able to dim the light below the set value.
Values: 1 – 99 (%). Default: 1.
Size: 1 byte dec
Parameter 11: Set the maximum brightness level (in %) for your dimmer. You won’t be able to add brightness to the light beyond the set value. Note: if Parameter 12 is set to value 0, Parameter 11 is automatically disabled.
Values: 1 – 99 (%). Default: 99.
Size: 1 byte dec
Double Tap and Single Tap Behavior
Parameter 12: Choose what you'd like the dimmer to do when you double-tap the upper paddle.
Values: 0 – the light will turn on to full brightness (default); 1 – the light will turn on to the custom brightness level set in parameter 18; 2 – the light will turn on to the maximum brightness level set in Parameter 11; 3 – double tap disabled.
Size: 1 byte dec
Parameter 25: Choose what you'd like the dimmer to do when you tap the upper paddle once.
Values: 0 – the light will turn on to the last brightness level (default); 1 – the light will turn on to the custom brightness level set in parameter 18; 2 – the light will turn on to the maximum brightness level set in Parameter 11; 3 – the light will turn on to full brightness.
Size: 1 byte dec
Enable/Disable Scene Control
Parameter 13: Enable or disable scene control functionality for quick double tap triggers.
Values: 0 – scene control disabled (default). 1 – scene control enabled.
Size: 1 byte dec
Smart Bulb Mode: Enable/Disable Paddle / Z-Wave Control
Parameter 15: Enable or disable paddle on/off control (aka disable the relay). If disabled, you’ll only be able to control the connected light via Z-Wave. Scenes and other functionality will still be available through paddles.
Values: 0 – physical paddle control disabled. 1 – physical paddle control enabled (default). 2 – physical paddle and Z-Wave control disabled.
NOTE: hold the lower paddle for 10 seconds until the LED indicator starts blinking, then within 2 seconds, tap the upper paddle 5 times quickly to change this mode. The LED indicator will stay solid green for 3 seconds to confirm the change.
FOR FIRMWARE 10.40, 2.30, 3.20, AND 4.10 (800LR) (or higher): Hold the UPPER paddle for 10 seconds until the LED indicator starts blinking, then within 2 seconds, tap the upper paddle 5 times quickly to change this mode. The LED indicator will stay solid green for 3 seconds to confirm the change.
Size: 1 byte dec
Parameter 20: Choose how you'd like the dimmer to report when paddles are tapped and held and physical / Z-Wave control is enabled or disabled.
Values: 0 – send basic set report for each brightness level to hub when physical / Z-Wave control is disabled for physical dimming when paddles are manually pressed / held; report final brightness level only (basic set report) for physical dimming when paddles are manually pressed / held and physical / Z-Wave control is enabled; always report final brightness level only (via multilevel reports) for Z-Wave control regardless of the physical / Z-Wave control mode. 1 – report final brightness level only for physical dimming, regardless of the physical / Z-Wave control mode. 2 – send multilevel report for each brightness level to hub when physical / Z-Wave control is disabled for physical dimming when paddles are manually pressed / held; report final brightness level only (multilevel report) for physical dimming when paddles are manually pressed / held and physical / Z-Wave control is enabled; always report final brightness level only (via multilevel reports) for Z-Wave control regardless of the physical / Z-Wave control mode. Default: 2.
Size: 1 byte dec
Parameter 21: Set reporting behavior for disabled physical control.
Values: 0 – switch reports on/off status and changes LED indicator state even if physical and Z-Wave control is disabled (default). 1 – switch doesn't report on/off status or change LED indicator state when physical (and Z-Wave) control is disabled.
Size: 1 byte dec
Physical Dimming Speed
Parameter 16: Set the time it takes to get from 0% to 100% brightness when pressing and holding the paddle (physical dimming). The number entered as value corresponds to the number of seconds.
Values: 1 – 99 (seconds). Default: 5.
Size: 1 byte dec
Remote Z-Wave Dimming Duration (Multilevel Commands For Group 3 And 4)
Parameter 30: Set the time it takes to get from 0% to 100% brightness on dimmers and smart bulbs directly associated with your dimmer in Groups 3 and 4 when pressing and holding the paddle (physical dimming) on your dimmer. The number entered as value corresponds to the number of seconds.
Values: 1 – 99 (seconds). Default: 5.
Size: 1 byte dec
Custom Brightness Level On
Parameter 18: Set the custom brightness level (instead of the last set brightness level) you want the dimmer to come on to when you single tap or double tap the upper paddle (see parameters 12 and 25).
Values: 0 – last brightness level (default); 1 – 99 (%) for custom brightness level.
Size: 1 byte dec
Night Light Mode
Parameter 22: Set the brightness level the dimmer will turn on to when off and when the lower paddle is held DOWN for 2.5-3 seconds.
Values: 0 – feature disabled; 1 – 99 (%). Default: 20.
Size: 1 byte dec
Enable/Disable Programming on the Paddles
Parameter 26: Enable or disable programming functionality on the dimmer paddles. If this setting is disabled, then inclusion, exclusion, smart bulb mode no longer work when dimmer paddles are activated (factory reset and scene control will still work) - that means you can now use triple-tap triggers on the dimmer for scenes and remote control of other devices.
Values: 0 – programming enabled (default). 1 – programming disabled.
Size: 1 byte dec
MANUAL CONTROL
Upper Paddle:
1 x tap: load on to last / custom / full / max brightness; Scene 1, attribute 00
2 x tap: on to full / max / custom brightness; Scene 1, attribute 03
3 x tap: enter inclusion (pairing) mode (only if not included to Z-Wave network); Scene 1, attribute 04
4 x tap: Scene 1, attribute 05
5 x tap: Scene 1, attribute 06
6 x tap: change LED indicator mode (see parameter 2)
press and hold: increase brightness level; Scene 1, attribute 01
release: Scene 1, attribute 02
held for 10 seconds (LED indicator starts blinking): enter the setting menu >> 5 x tap up to change smart bulb mode (see parameter 15)
Lower Paddle:
1 x tap: load off; Scene 2, attribute 00
2 x tap: Scene 2, attribute 03
3 x tap: enter exclusion (unpairing) mode; Scene 2, attribute 04
4 x tap: Scene 2, attribute 05
5 x tap: Scene 2, attribute 06
press and hold: decrease brightness level; Scene 2, attribute 01
press and hold when off: turn on to 20% brightness (night light mode)
release: Scene 2, attribute 02
held for 10 seconds (LED indicator starts blinking): enter the setting menu >> 5 x tap down for factory reset; 2 x tap down to enable the range test tool.
Supported command classes:
COMMAND_CLASS_ZWAVEPLUS_INFO,
COMMAND_CLASS_SWITCH_MULTILEVEL_V4,
COMMAND_CLASS_CONFIGURATION,
COMMAND_CLASS_CENTRAL_SCENE_V3,
COMMAND_CLASS_ASSOCIATION,
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V2,
COMMAND_CLASS_ASSOCIATION_GRP_INFO,
COMMAND_CLASS_TRANSPORT_SERVICE_V2,
COMMAND_CLASS_VERSION,
COMMAND_CLASS_MANUFACTURER_SPECIFIC,
COMMAND_CLASS_DEVICE_RESET_LOCALLY,
COMMAND_CLASS_INDICATOR,
COMMAND_CLASS_POWERLEVEL,
COMMAND_CLASS_SECURITY_2,
COMMAND_CLASS_SUPERVISION,
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5
How to Access the Advanced Settings:
All ZEN77 dimmers can be updated via OTA firmware updates, here is how to do that. You can access all firmware files here once you register your product and create an account here. Need more help? Feel free to reach out to our support team, we're here 7 days a week!
