How to Add Your ZAC36 Titan Valve Actuator to Alarm.com

The ZAC36 Titan Valve Actuator is now integrated with Alarm.com. A smart flood protection system can be the difference between thousands of dollars in water damage & a safe, secure home. Flooding causes an average of $8.2 billion in damages annually. Protect your home with this reliable hardware, backed by secure Z-Wave technology.
The Titan installs directly on your existing ball valve in just under two minutes, without any tools needed. You can mount it indoors or outdoors & it's strong enough to handle even the most stubborn valve. It comes with a connected leak probe that works offline to help you protect your home in all situations.

Are you an Alarm.com installer? Scroll to the installer instructions for MobileTech instructions. Long Range? Scroll to the bottom of the article:

Follow the simple steps below to add your ZAC36 Titan Valve Actuator to Alarm.com:

Standard Mesh Inclusion Instructions

From the Home screen choose More > click + Add Device > click Z-Wave Device:

Click Next > wait while the system prepares to add the device > click Next:

Start inclusion on the ZAC36 by tapping the Z-Wave button on the device 3 times quickly - make sure you hear a beep each time you tap the button (if you don't hear it, please try again). It's a touch button so simply place your finger on it, there will be no tactile feedback like on a push button > input the 5-digit pin code located by the QR code on the device or the box > click Continue:

The hub will complete inclusion. This can take a few minutes depending on signal strength and how busy your network is > the ZAC36 will be added with the generic name "Water Valve" with the node ID at the end. Here you can re-name your device; when named, click Next and Done.

If you have trouble including the device, try excluding it first. This is a standard Z-Wave function and can be done with any Z-Wave device on any Z-Wave hub at any time, regardless of the devices inclusion status. This means that even if the device has never been included, is currently not included, or is even included to another hub that might not be responsive, you can still exclude it from the new hub. Exclusion simply acts as a soft Z-Wave reset that prepares the device for inclusion and resolves most inclusion or configuration issues. Check out the exclusion process for the ZAC36 on Alarm.com here.

Installer / Partner Portal / MobileTech Standard Mesh Inclusion Instructions

A Z-Wave network is established by putting a Z-Wave controller into Add Mode and triggering devices (or nodes) to join the network.
Tips for setting up a Z-Wave network:

Before adding devices to the network, make sure to put the devices in their final locations if possible. This way, the network can correctly identify the strongest communication pathway for each device.
Always add devices closest to the panel first, and work outwards from there. Devices that have already been added can relay the panel’s Add Mode signal to add farther devices to the network.
Verify each device adds successfully before moving on to the next device. The panel, Partner Portal, or MobileTech app indicates when a device has been added to the network.

To add Z-Wave devices using the Partner Portal with standard Z-Wave mesh inclusion:

Log into the Partner Portal.
Find the customer account.
Click Equipment.
Click Z-Wave Devices.
In Manage Devices, click Add a Z-Wave Device.
Wait for the bold message: Checking for new devices on the network.
Initiate inclusion on the ZAC36 Titan by tapping the Z-Wave button on the device 3 times quickly - make sure you hear a beep each time you tap the button (if you don't hear it, please try again). It's a touch button so simply place your finger on it, there will be no tactile feedback like on a push button
When a device is added successfully, it shows up on this screen following a 30-second delay.
Continue triggering devices. Several devices may be added to the network without re-entering Add Mode.
Once all desired devices are added, click Exit.
Devices should show up on the Alarm.com customer website and app, Partner Portal, and MobileTech app within 5 minutes of adding the devices.

To add Z-Wave devices using the MobileTech app with standard Z-Wave mesh inclusion:

Log into the MobileTech app.
Find the customer account.
If possible, move all Z-Wave devices to their final location on the property.
Tap Equipment.
Tap Z-Wave Devices.
Tap to expand Z-Wave Actions.
Tap Add Z-Wave Devices.
Wait for the bold message: Checking for new devices on the network.
Initiate inclusion on the ZAC36 TItan by tapping the Z-Wave button on the device 3 times quickly - make sure you hear a beep each time you tap the button (if you don't hear it, please try again). It's a touch button so simply place your finger on it, there will be no tactile feedback like on a push button.
When a device is added successfully, it shows up on the screen following a 30-second delay.
Continue triggering devices. Several devices may be added to the network without re-entering Add Mode.
Once all desired devices are added, tap Exit.
Devices should show up on the Alarm.com customer website and app, Partner Portal, and MobileTech app within 5 minutes of adding the devices.

Long Range Inclusion Instructions for Installer / Partner Portal / MobileTech

Alarm.com supports Z-Wave Long Range (Z-Wave LR). Z-Wave LR allows for even more Z-Wave devices on a single system without the need for repeaters. Both the panel and device must be Z-Wave LR-enabled.

To add the ZAC36 700 LR via Long Range inclusion using the Partner Portal:
1. Log into the Partner Portal.
2. Find the customer account.
3. Click Equipment.
4. Click Z-Wave Devices.
5. In Manage Devices, click Manage S2 & SmartStart Keys.
6. Click Add Key.
7. Enter a name for the ZAC36 Valve Actuator.
8. Use a USB barcode scanner and enter the data in QR Code or click Scan to use the computer/mobile device's built-in camera to scan the device's barcode and automatically populate the information. Note: The internet browser must be given permission to access the built-in camera before it can scan the barcode.
9. Click Add Device.
10. In the Add a Device Key check Use Long Range. Note: This option will not be available if the device or panel do not support Z-Wave LR.
11. Click Add Device.
12. The device should now automatically be enrolled into the Z-Wave network when powered up. Multiple device keys can be added before powering up if desired. Note: If adding multiple device keys, it is recommended to power each device up about a minute apart to ensure a smoother enrollment.
13. Once included, the device will appear as Included in the Active Keys column on the Manage S2 & SmartStart Keys page.

To add the ZAC36 700 LR via Long Range inclusion using the MobileTech app:
1. Log into the MobileTech app.
2. Find the customer account.
3. Tap Equipment.
4. Tap Z-Wave Devices.
5. Tap to expand Z-Wave Actions.
6. Tap Scan Device To Add.
7. Tap Scan Now to scan the device's barcode and automatically populate the information.
8. In Device Name enter a name for the device.
9. Tap Use Long Range to enable Z-Wave LR. Note: This option will not be available if the device or panel do not support Z-Wave LR.
10. Tap Add Device.
11. The device should now automatically be enrolled into the Z-Wave network when powered up. Multiple device keys can be added before powering up if desired. Note: If adding multiple device keys, it is recommended to power each device up about a minute apart to ensure a smoother enrollment.
12. Once included, the device will appear as Included in the Active Keys column on the Manage S2 & SmartStart Keys page.

Please don't hesitate to reach out with any questions you may have!