How to Add Your ZEN05 Outdoor Smart Plug to Z-Box
You don't need any extra device handlers or drivers here! The ZEN05 Outdoor Smart Plug will be recognized correctly on the Z-Box, as it is fully integrated. Simply plug in the device, then follow the steps below to add the device to your Z-Box hub. You can add a new device via the web interface, or the mobile app. Ch…
How to Add Your ZSE43 Tilt | Shock XS Sensor to the Z-Box Hub
The ZSE43 Tilt | Shock Sensor will configure correctly on the Z-Box out of the box; no need for drivers or custom handlers! You can add the sensor using the Z-Box web interface or the Z-Box Hub mobile app, and we've included instructions below for both methods: If you're running Z-Box firmware release 5.172.18 or hi…
How to Add Your ZEN34 Remote Switch to the Z-Box Hub
Easily add the ZEN34 Remote Switch to your Z-Box Hub and for quick and intuitive programming out of the box. If you're running Z-Box firmware release 5.172.18 or higher, you have the option to include your Z-Wave Long Range (ZWLR) supporting devices via the new Long Range protocol. Adding via ZWLR can be done both v…
How to Add Your ZSE70 Outdoor Motion Sensor to SmartThings
Ready to include your new ZSE70 Outdoor Motion Sensor to SmartThings? Check out the instructions below! You will need to install the lua Edge driver to access advanced settings and ensure the device is properly recognized and configured on SmartThings. With the driver installed, you can proceed to auto-include or …
How to Add Your ZSE42 Water Leak XS Sensor to the Z-Box Hub
The ZSE42 Water Leak Sensor will be recognized correctly on the Z-Box right out of the box, without any drivers or custom handlers! You can add the sensor using the Z-Box web interface or the Z-Box Hub mobile app, and we've included instructions below for both methods. If you're running Z-Box firmware release 5.172.…
How to Add Your ZAC36 Titan Valve Actuator to the Z-Box Hub
The ZAC36 Titan Valve Actuator is fully integrated with the Z-Box Hub and will be easily recognized by the hub out of the box. Simply follow the steps below to add the switch to your system. The Titan will fit on valves up to 1.25". Is your pipe larger? Reach out to us about an extension kit for the ZAC36 to accomm…
How to Add Your ZEN16 MultiRelay to the Z-Box Hub
With full support by Z-Box out of the box, it's quick and easy to add your ZEN16 MultiRelay to the Z-Box Hub and have fun customizing your device. If you're running Z-Box firmware release 5.172.18 or higher, you have the option to include your Z-Wave Long Range (ZWLR) supporting devices via the new Long Range protoc…
How to Add Your ZEN53 DC Motor Controller to your Z-Wave Hub
Once the device is installed correctly and powered with a proper 6-32 VDC power supply, adding the device to your Z-Wave hub is quick and easy! Simply follow the steps below to have the ZEN53 included in no time! Important Note : A steady, blinking green is the standard state for the device; as long as the unit has …
How to Add Your ZEN15 Power Switch to the Z-Box Hub
The ZEN15 Power Switch is fully supported by Z-Box and will be recognized out of the box, so inclusion is easy! If you're running Z-Box firmware release 5.172.18 or higher, you have the option to include your Z-Wave Long Range (ZWLR) supporting devices via the new Long Range protocol. Adding via ZWLR can be done bot…
How to Add Your ZEN53 DC Motor Controller to Z-Box
The ZEN53 will be recognized correctly on the Z-Box out of the box, no handlers or drivers needed! You can add the ZEN53 using the Z-Box web interface or the Z-Box Hub mobile app, and we've included instructions below for both! Important Note : A steady, blinking green is the standard state for the device; as long a…
