-
How to Add Your ZEN55 Smoke & CO Detector Bridge to Z-Box
Inclusion is fast and easy with the Z-Box! You don't need any extra device handlers or drivers here! The ZEN55 Smoke & CO Detector Bridge will be recognized correctly on the Z-Box, as it is fully integrated. Simply follow the instructions in the manual to install and power the device, then follow the steps below to a…
-
How to Add Your ZSE70 Outdoor Motion Sensor to SmartThings
Ready to include your new ZSE70 Outdoor Motion Sensor to SmartThings? Check out the instructions below! You will need to install the lua Edge driver to access advanced settings and ensure the device is properly recognized and configured on SmartThings. With the driver installed, you can proceed to auto-include or …
-
How to Add Your ZEN51 Dry Contact Relay to Vera
Adding your ZEN51 Dry Contact Relay to Vera is quick and simple. Below are the steps to pair your device: * Power on the ZEN51 * In your Vera app, select the Devices tab. Next, click on the gray " + Add Device " button * Choose Generic Z-Wave Device from the device list * Click the Z-Wave button on the re…
-
How to Add Your ZSE43 Tilt | Shock XS Sensor to Your Z-Wave System
Adding or pairing a device to your Z-Wave system is called Inclusion. You'll need to include your ZSE43 sensor to your network before mounting it in its final location. To auto-include your ZSE43 Tilt | Shock XS Sensor: * Put your Z-Wave hub into inclusion/pairing mode (see your hub's manual for instructions …
-
How to Add Your ZEN17 Universal Relay to Vera
You'll have your Universal Relay paired to your Vera hub in no time! Before including your device, ensure the ZEN17 is properly powered. The power supply only provides power to the Z-Wave chip and electronics within the unit. Therefore, the power supply doesn't need to be rated for a lot of power, * USB C with a …
-
How to Add Your ZEN77 S2 Dimmer to Vera
Have your ZEN77 Dimmer added to your Vera network in no time! * Select the Devices tab in your Vera app. Then click on the gray " + Add Device " button * Choose Generic Z-Wave Device from the device list * Tap the UPPER paddle 3 times quickly (The LED indicator should flash in blue to confirm it has signal …
-
How to Add Your ZEN71 On/Off Switch to the Z-Box Hub
The switch is fully integrated with the Z-Box Hub and will be recognized by the hub out of the box. Follow the steps below to add the switch to your system. If you're running Z-Box firmware release 5.172.18 or higher, you have the option to include your Z-Wave Long Range (ZWLR) supporting devices via the new Long Ra…
-
How to Add the ZSE11 Q Sensor to Vera
Add the ZSE11 Q Sensor to you Vera hub in no time! No additional configuration is needed, but you may need to wake it up the sensor a few times by clicking the Z-Wave button 3 times quickly after it's added so it's fully configured. Here's how to include the device: 1 . Power the sensor by USB or battery and br…
-
How to Add Your ZEN24 Toggle Dimmer Switch to Hubitat
This is product is discontinued and replaced with the ZEN74 . What does that mean? The ZEN24 switch will quickly pair to your hub as it is officially integrated with Hubitat. For Hubitat C-7 hub users, your S2 security level for the ZEN24 should be S2 Unauthenticated. Make sure to select this when prompted so…
-
How to Add Your ZSE41 Open | Close XS Sensor to Vera
Pairing your ZSE41 XS Sensor is easy! Here are the steps for adding the ZSE41 to Vera: * Power the ZSE41 Sensor up. * Select the Devices tab in your Vera app. Then click on the gray " + Add Device " button. * Choose Generic Z-Wave Device from the device list * Press and release the Z-Wave button 3 times a…
Looking for Z-Box Hub Support? Please click here to access the Z-Box Hub Support Portal.
