How to Add Your ZEN26 On/Off Switch to Hubitat
Hubitat integrated the ZEN26 Switch to make inclusion easier right out of the box. You'll want to select S2 Unauthenticated security for your ZEN26 if you're using a Hubitat C-7 hub, if it isn't already selected during pairing. Users of older Hubitat hubs can simply skip this and go ahead to the inclusion steps …
My Bulbs Glow When My ZEN26 or ZEN27 Switch is Turned Off
While rare, we've seen this issue with ZEN26 and ZEN27 switches when used with lower-quality low-wattage bulbs. The ZEN26 switches use a special double relay to accommodate the unique 3-way solution and allow some current flowing between the regular mechanical switch and smart switch for electrical status updates. F…
Can't Add My ZEN26 On/Off Switch to My Z-Wave System
Let's start by excluding the switch. It may sound counter-intuitive, but exclusion is just a reset. A device doesn't need to be included to be able to be excluded. Here's how to do it: 1. Bring your Z-Wave hub as close to the switch as possible 2. Put your Z-Wave controller into exclusion mode 3. Tap the LOWER pad…
How to Turn Off the LED Indicator on Your ZEN26 Switch
S2 Paddle Switches give you two ways to control your switch's LED indicator. If your Z-Wave hub allows access to advanced settings and parameter input, you can enable and disable the LED indicator by going to your hub's app interface and changing the value for Parameter 2 (here's how to do that in Vera and SmartT…
Can't Add My ZEN26 On/Off Switch to SmartThings
Exclude to include? Sounds weird, but exclusion is like a reset and we find it helps with all types of inclusion and configuration issues! The ZEN26 switch will work with SmartThings out of the box. We recommend you install the lua Edge driver to customize your device. If you're seeing inclusion issues with your s…
My ZEN26 On/Off Switch Won't Turn the Lights On
Let's see if something about the installation can be improved: Here's our general wiring guide for Zooz S2 switches (wiring guide coming soon). If you have the switch installed in a multi-point set-up like a 3-way, 4-way, or 5-way (additional diagrams coming soon), make sure to refer to the relevant diagrams and t…
ZEN26 S2 On/Off Switch & Compatible Hubs
Will the ZEN26 S2 On/Off Switch work with my hub? The switch works great with the following Z-Wave systems: * Z-Box Hub (recommended for all Zooz products) * 2GIG (no advanced settings available) * ADT Pulse (no advanced settings available) * Alarm.com (no advanced settings available) * Almond (Securify) * F…
ZEN26 S2 Switch Change Log
Here is a log of upgrades and improvements we made to the S2 ZEN26 model so far. VER. 1.0 (released 10/2018) Original release. Hardware: * Included new Simple Direct 3-Way Firmware: 1.0 * Included S2 security, OTA firmware updates, built-in auto-off timer (set in seconds) VER. 2.0 (released 6/2019) Hardware…
ZEN26 S2 On/Off Switch VER. 3.02 Advanced Settings
Here is a full list of advanced settings (parameters) for ZEN26 On/Off Switch VER. 3.02 firmware: On/Off Paddle Orientation Parameter 1: Choose if you want the upper paddle to turn the light on or turn the light off when tapped. Values: 0 – Upper paddle turns the light on, lower paddle turns it off (default); 1 …
ZEN26 S2 On Off Switch Specs
Here are the technical details for the S2 Switch ZEN26: * Z-Wave Signal Frequency: 908.42 MHz * Power: 120 V, 60 Hz * Maximum Load: 8 A, 150 W LED, 600 W incandescent * Range: Up to 100 feet line of sight * Installation and Use: Indoor Only * Operating Temperature: 32-104° F (0-40° C) * Dimensions: 4 1…
