My ZSE41 Open | Close XS Sensor Shows Offline in Hubitat
A range or configuration issue could cause your ZSE41 Open|Close XS sensor to show up as “offline” in Hubitat. Try a Z-Wave Network Repair! Ensure your Hubitat hub is up to date on its platform version. Follow these steps to run the Z-Wave Repair to refresh your Z-Wave mesh network connections: * Open Hubitat …
How to Add Your ZEN54 0-10 V Dimmer to Hubitat
Do you have the ZEN54 correctly powered and installed? Great! Now it's time to include the device to your Hubitat hub. Including the ZEN54 0-10V Dimmer to Hubitat is simple! Follow the steps below to quickly and easily add the ZEN54 to Hubitat. Please install the custom driver prior to adding the device to help it b…
How to Access Advanced Settings for My ZEN54 0-10 V Dimmer on Hubitat
The ZEN54 0-10 V Dimmer should be integrated with Hubitat soon. In the meantime, please install the custom driver below to access the advanced settings and configure the device. Please check that your hub is operating on the latest Hubitat platform version first, then follow these step-by-step instructions to inst…
My ZEN73 On/Off Toggle Switch is Offline in Hubitat
A Network Repair can help improve communication between Hubitat and your ZEN73 switch if it is showing “offline” in Hubitat. See if your Hubitat platform is updated to the latest version before performing a Z-Wave Network Repair. It’s an easy process to repair your network connections in Hubitat. Here are the ste…
My ZEN76 S2 Switch is Offline in Hubitat
An “offline” status in Hubitat could mean your ZEN76 switch is out of range or hasn’t configured properly. Running a Z-Wave Network Repair may solve the problem. First, you’ll want to verify your Hubitat platform is updated to the latest version. Then you can follow these steps to run the repair on your network conn…
Can't Add My ZEN73 On/Off Toggle Switch to Hubitat
Not able to include the ZEN73 to Hubitat? It's time to try exclusion! Removing the switch from your hub is possible, even if it’s never been added. An “unknown” device will be excluded and you can then try to include it again. Just make sure your Hubitat is running on the latest version first. However, please not…
My ZEN52 Double Relay Shows Offline in Hubitat
Does the ZEN52 Double Relay show as “offline" in Hubitat? This suggests a range or configuration issue. A Z-Wave Network Repair could help. Ensure your Hubitat hub is up to date on its platform version. Next, utilize the steps below to run the Z-Wave Repair to refresh your Z-Wave mesh network connections: * Open…
How to Access Advanced Settings for the ZEN14 Double Outdoor Plug on Hubitat
Follow the steps below to install the community driver and access to the advanced settings for the ZEN14 Double Plug! Hubitat is in the process of integrating the Double Plug, so in the meantime, please use the community driver. Here's how to install the community driver: * Open Hubitat in your browser. * Clic…
My ZEN77 S2 Dimmer is Offline in Hubitat
If your ZEN77 is showing as “offline” in Hubitat, it may be out of range or not configured properly. The issue could be resolved with a simple Z-Wave Network Repair. You’ll want to check that your Hubitat platform is running on the most up-to-date version first. Once you’ve done that, you can try repairing your netw…
Can't Add My ZSE43 Tilt|Shock XS Sensor to Hubitat
The ZSE43 XS Sensor is officially supported by Hubitat so it will work with the hub out of the box as long as the platform is on version 2.2.9 or higher. To help with the ZSE43 Sensor configuration, try the exclusion process first. This can be done even if it was never connected to the hub, as it acts as a soft rese…
