How to Add Your ZSE43 Tilt | Shock XS Sensor to the Z-Box Hub
The ZSE43 Tilt | Shock Sensor will configure correctly on the Z-Box out of the box; no need for drivers or custom handlers! You can add the sensor using the Z-Box web interface or the Z-Box Hub mobile app, and we've included instructions below for both methods: If you're running Z-Box firmware release 5.172.18 or hi…
How to Add Your ZSE42 Water Leak XS Sensor to the Z-Box Hub
The ZSE42 Water Leak Sensor will be recognized correctly on the Z-Box right out of the box, without any drivers or custom handlers! You can add the sensor using the Z-Box web interface or the Z-Box Hub mobile app, and we've included instructions below for both methods. If you're running Z-Box firmware release 5.172.…
How to Add Your ZEN16 MultiRelay to the Z-Box Hub
With full support by Z-Box out of the box, it's quick and easy to add your ZEN16 MultiRelay to the Z-Box Hub and have fun customizing your device. Before including your device, ensure the ZEN16 is properly powered. The power supply only provides power to the Z-Wave chip and electronics within the unit. Therefore, th…
How to Add Your ZEN53 DC Motor Controller to your Z-Wave Hub
Once the device is installed correctly and powered with a proper 6-32 VDC power supply, adding the device to your Z-Wave hub is quick and easy! Simply follow the steps below to have the ZEN53 included in no time! Important Note : A steady, blinking green is the standard state for the device; as long as the unit has …
How to Add Your ZAC36 Titan Valve Actuator to the Z-Box Hub
The ZAC36 Titan Valve Actuator is fully integrated with the Z-Box Hub and will be easily recognized by the hub out of the box. Simply follow the steps below to add the switch to your system. The Titan will fit on valves up to 1.25". Is your pipe larger? Reach out to us about an extension kit for the ZAC36 to accomm…
How to Add Your ZSE70 Outdoor Motion Sensor to SmartThings
Ready to include your new ZSE70 Outdoor Motion Sensor to SmartThings? Check out the instructions below! You will need to install the lua Edge driver to access advanced settings and ensure the device is properly recognized and configured on SmartThings. With the driver installed, you can proceed to auto-include or …
How to Add Your ZEN53 DC Motor Controller to Z-Box
The ZEN53 will be recognized correctly on the Z-Box out of the box, no handlers or drivers needed! You can add the ZEN53 using the Z-Box web interface or the Z-Box Hub mobile app, and we've included instructions below for both! Important Note : A steady, blinking green is the standard state for the device; as long a…
How to Add Your ZEN73 On/Off Switch to the Z-Box Hub
The ZEN73 Toggle Switch will be recognized by the hub out of the box, no need for any custom drivers, as it is fully integrated with the Z-Box Hub. Follow the steps below to add the switch to your system. If you're running Z-Box firmware release 5.172.18 or higher, you have the option to include your Z-Wave Long Ran…
How to Add Your ZEN53 DC Motor Controller to SmartThings
Ready to add your ZEN53 DC Motor Controller to SmartThings? The process is quick and easy! Just follow the simple steps below to have your Motor Controller included to SmartThings. You'll be able to control the device connected to your Motor Controller from the app, create on/off schedules for it and use it in more c…
How to Add Your ZEN54 0-10 V Dimmer to the Z-Box Hub
No need for any extra device handlers or drivers here! The ZEN54 will be recognized correctly on the Z-Box right out of the box! Once the device is installed correctly and powered, inlcuding the device to your Z-Box Hub is quick and easy. You can add the dimmer using the Z-Box web interface or the Z-Box Hub mobile ap…
