-
How to Add Your ZEN27 Dimmer to SmartThings
Before moving on to Z-Wave set up, check that your dimmer works at 100% manually. Once you verify that it works well locally, it's time to add the dimmer to SmartThings. The switch will work with the out of the box; however, we recommend installing the lua Edge driver first to provide access to all the advanced fe…
-
How to Add Your ZEN27 Dimmer to Your Z-Wave System
First, check that your dimmer is working well manually, that you have full dimming and on/off control directly from the device. Once that's settled, we can include the unit to your Z-Wave system. There are many words for it depending on the system you're using, but our standard term for it is "inclusion." Inclusion …
-
ZEN27 S2 Dimmer Specs
Here are the technical details for the S2 Dimmer ZEN27: * Z-Wave Signal Frequency: 908.42 MHz * Power: 120 V, 60 Hz * Maximum Load: 100 W LED, 300 W incandescent (200 W with one side of heat sink tabs off, 100 W with both sides of tabs off) * Range: Up to 100 feet line of sight * Installation and Use: Indo…
-
How Do I Perform Hard Reset on My ZEN27 Dimmer?
Hard reset can help with a variety of configuration issues. It's also a good idea to try reset if your dimmer is unresponsive to Z-Wave commands, especially if you already gave exclusion a try without any luck. Tap-tap-tap’n’hold the upper paddle for 10 seconds or more to reset the dimmer. The LED indicator w…
-
Minimum Load Requirement - Why It's There
Why is there a 15W / 20W minimum load required for some of our dimmers? Our recommendation is to have at least 15 Watts of load connected to your Zooz ZEN22, ZEN24, ZEN72, ZEN74, and ZEN77 VER 3.0/4.0 dimmers even though chances are the switch will work just fine with a single LED bulb as well. It's quite random how…
-
How to Access Advanced Settings for My ZEN27 Dimmer on SmartThings
With the latest transition to the lua platform , SmartThings will no longer support groovy-based device handlers. Don't worry, we've created a new custom Edge driver for the ZEN27 Switch for the lua platform! Below are the instructions on how to install the new Edge driver. If you haven't added one before, just fol…
-
ZEN27 S2 Dimmer VER. 3.01 Advanced Settings
Here is a full list of advanced settings (parameters) for ZEN27 S2 Dimmer VER. 3.01 firmware: On/Off Paddle Orientation Parameter 1: Choose if you want the upper paddle to turn the light on or turn the light off when tapped. Values: 0 – Upper paddle turns the light on, lower paddle turns it off (default); 1 – Up…
-
ZEN27 S2 Dimmer Change Log
Here is a list of updates we made to the S2 ZEN27 model so far. VER. 1.0 (released 10/2018) Original release. Hardware: * Included new Simple Direct 3-Way Firmware: 1.0 * Included S2 security, OTA firmware updates, full ramp control, double tap from off to full brightness VER. 2.0 (released 3/2019) Hardware…
-
ZEN2X vs ZEN7X Models: What's the Difference
You may have noticed our Zooz light switches line has expanded. We just love updating and upgrading products for you! So what's the difference between the new 700/800LR series switches and the 500 series models? Here is a short list of upgrades we implemented in the 700/800LR series models: * 700/800 series Z-W…
-
Can My Zooz Switch Be Used with Add-Ons, Dimmers, or Another Z-Wave Switch?
While Zooz switches cannot be directly wired to other smart switches or electronic add-on switches, you can make two Zooz switches work together using remote Z-Wave control. Remember, always wire your Zooz switches according to the appropriate diagram from the manual for the model you're installing. Zooz switches in…
Looking for Z-Box Hub Support? Please click here to access the Z-Box Hub Support Portal.
